Which types of cranes can be retrofitted with a new control system?

Almost any crane type can be retrofitted with a new control system, regardless of brand or age. The steel structure of a crane has a far longer service life than its electronics, which means that when a safe load indicator, load moment indicator, or rated capacity indicator reaches the end of its useful life, the crane itself does not need to be scrapped. A retrofit replaces the control and safety electronics while the crane stays in service, and this article works through the most common questions crane owners and technical managers have about that process.

What crane components are typically replaced during a retrofit?

During a crane control system retrofit, the electronic and sensing components are replaced while the crane’s structural steel, hoist, and drive systems remain untouched. The parts that are upgraded include the main controller or display unit, force sensors such as load cells and load pins, angle sensors, length sensors, pressure transducers, and the operator interface. Wiring harnesses and junction boxes are often replaced at the same time.

The goal is to restore full functionality using current technology. In practice, this means replacing a legacy safe load indicator or load moment indicator with a modern equivalent that performs the same calculations and outputs the same safety signals. Where original sensors are no longer available, modern alternatives such as 4…20 mA force sensors can be integrated with the new controller. We have completed installations where a crane built in 1998 was returned to full working order by pairing a DS130 safe load indicator controller with updated force transducers, because the original transducers were simply no longer obtainable.

Ancillary systems such as anti-two-block switches, wind speed sensors, CCTV cameras, and data loggers can also be replaced or added during the same mobilisation, reducing downtime and cost compared with separate service visits.

Can mobile cranes be retrofitted with a new control system?

Yes, mobile cranes are among the most common candidates for a crane control system retrofit. This includes all-terrain cranes, rough-terrain cranes, truck-mounted cranes, and crawler cranes. Brands such as Liebherr, Tadano, Grove, Manitowoc, Kobelco, Sany, XCMG, Zoomlion, Fassi, Effer, Palfinger, and many others have legacy systems that can be replaced with the DS130 safe load indicator or DS430 load moment indicator from our current DSx30 platform.

Mobile cranes present a particular case for modernisation because they operate across multiple sites and are exposed to vibration, dust, and weather that accelerate wear on electronics. When an older system such as a PRS145, DS350G, DS350C, or AS110 reaches a point where spare parts or software support are difficult to obtain, a retrofit to a current platform restores reliability without removing the crane from the fleet.

For articulated truck-mounted cranes and knuckle boom cranes, the same principle applies. Brands including Fassi, Effer, and Palfinger with legacy DS100 or AS110 systems are supported. The DS130 and DS430 platform is designed to accept the sensor inputs used by these older systems, which simplifies the installation and reduces the amount of new cabling required.

Are offshore and marine cranes compatible with retrofit systems?

Offshore and marine cranes are fully compatible with crane safety system upgrades, and in many cases the harsh operating environment makes modernisation more urgent than for land-based equipment. Pedestal cranes, offshore knuckle boom cranes, ship-to-shore cranes, and marine deck cranes all fall within the scope of a retrofit programme.

We have replaced DS120 systems with DS130 safe load indicator systems on ZPMC ship-to-shore cranes, demonstrating that even large port and terminal cranes can be modernised without structural intervention. Brands such as NPMC, Gottwald, Sormec, Sumitomo, and DG Crane with legacy systems including the DS350G, DS350GW, DS100, and PRS145 are covered by the current DSx30 platform.

Offshore installations often require equipment certified to ATEX or IECEx standards for use in potentially explosive atmospheres. Our retrofit systems and associated sensors are available with the relevant certifications, and we also supply ATEX-certified CCTV and remote monitoring solutions that can be integrated during the same project. Details of applicable certifications are listed on our certifications page.

What types of overhead and gantry cranes can be retrofitted?

Overhead travelling cranes, bridge cranes, gantry cranes, and portal cranes can all receive a crane modernisation retrofit. These crane types are common in steel mills, shipyards, ports, and heavy manufacturing facilities, and their control systems are subject to the same obsolescence cycle as mobile crane electronics.

Brands such as Demag, Kone, and ZPMC appear in our compatibility records with legacy systems including the DS350G, DS350G/C, DS100, DS350C, and PDC. The DS130 safe load indicator and DS430 load moment indicator can replace these systems, restoring overload protection and load display functionality. For overhead cranes with multiple hoist points or complex lifting configurations, the DS430 supports the additional inputs and calculation modes required.

Winch force measurement and control is another common retrofit requirement for gantry and portal cranes. This can be addressed alongside the main safe load indicator replacement, integrating winch force sensors and control outputs into a single system rather than running separate equipment.

Which older or legacy cranes are still viable retrofit candidates?

Any crane whose steel structure is in serviceable condition is a viable candidate for a control system retrofit, regardless of age. The age of the electronics is a separate question from the age of the crane, and in many cases a crane manufactured in the 1980s or 1990s is structurally sound but carrying electronics that are decades past their expected service life.

The most common legacy systems we replace are the PRS145, DS350G, DS350C, DS100, AS110, and DS85/KD series. These appear across a wide range of brands including American Hoist, Cargotec, Caterpillar, Demag, Fassi, Faun, Fushun, Hitachi, Komatsu, Liebherr, Locatelli, Manitowoc, P&H, Sany, Sennebogen, Sumitomo, Tadano, and others. Additional legacy systems such as the PDC, ECIS, iFlex2, and iFlex5 are also covered for specific brands.

A crane that was built in 1998 and has had its original load cells fail due to age is not necessarily a candidate for scrapping. As demonstrated in one of our completed projects, fitting a DS130 safe load indicator controller and compatible modern force sensors restored the crane to full operational status. The key question is the structural and mechanical condition of the crane, not the vintage of its electronics.

How does a crane control system retrofit actually work?

A crane control system retrofit follows a structured process: assess the existing system, select compatible replacement hardware, remove the legacy equipment, install and wire the new system, calibrate sensors, and commission the crane with load testing. The process is managed by specialist engineers and typically takes place on site with the crane out of service for the minimum necessary period.

The assessment phase establishes which sensors are still functional and which need replacement, what cable routes are available, and what the new system needs to replicate in terms of outputs and interlocks. Because the DS130 and DS430 are designed to accept sensor types used by legacy systems, it is often possible to retain serviceable sensors and replace only the controller and display, reducing both cost and installation time.

Calibration is carried out using known test loads or calibrated reference equipment to verify that the new system reads accurately across the crane’s working range. Our field service team handles installation and commissioning worldwide, and we also provide remote access capability so that system parameters can be reviewed and adjusted without a return site visit where the installation allows it.

Documentation, including calibration records and system configuration data, is provided at handover. This supports ongoing maintenance and satisfies inspection requirements in most jurisdictions.

What certifications should a retrofit control system carry?

A retrofit control system should carry the certifications required by the jurisdiction where the crane operates and the nature of the working environment. For general industrial use, CE marking is the standard requirement in Europe. For offshore, petrochemical, or other potentially explosive atmospheres, ATEX certification is required in Europe, with IECEx recognised internationally and UL certification relevant for North American projects.

The DS130 safe load indicator and DS430 load moment indicator from our DSx30 platform are available with the certifications applicable to their installation environment. Sensors, load pins, and load cells supplied as part of a retrofit can also be provided with ATEX, IECEx, or UL certification where required. This matters because fitting a non-certified sensor into a certified system can invalidate the overall certification of the installation.

Beyond product certification, the retrofit process itself should be documented in a way that supports the crane’s ongoing inspection and recertification cycle. This includes calibration records, wiring documentation, and configuration data. Our system integration approach covers this documentation as part of the project deliverables, so that the crane owner has a complete record for their safety management system.

If you are managing a crane with a legacy safe load indicator, load moment indicator, or rated capacity indicator and need to assess your options, contact PAT-Krüger to discuss which replacement system fits your crane and operating environment. We can advise on compatibility, certification requirements, and the most practical route to getting your crane back to full operational status.

Related Articles